Valley Gutter & Ribbon Curb Contractor in Southeast Texas

Hollier Construction Services builds concrete valley gutter and ribbon curb for streets, intersections, and parking lots across Southeast Texas. Valley gutter carries runoff across or along pavement to an inlet or outfall. Ribbon curb is a low concrete edge that holds a pavement border in place. Hollier's slip-form machine lays valley gutter, and both tie into the surrounding concrete curb and gutter.

What Valley Gutter and Ribbon Curb Are

Valley gutter, also called cross gutter, is a shallow concrete channel set nearly flush with the pavement. Vehicles drive across it while runoff follows its low center line.

Ribbon curb is a narrow concrete band along a pavement edge. It sits at or close to pavement height and gives that edge a hard, straight border.

The two solve different problems. Valley gutter moves water across or along a paved surface. Ribbon curb holds an edge in place, often where water leaves the pavement as sheet flow instead of entering a channel.

Both differ from raised barrier or roll curb. Those profiles keep runoff in a gutter pan beside the curb face until an inlet picks it up.

Where Each One Is Used

The classic location for valley gutter is an intersection where one street's runoff has to cross another.

We could not find a valley gutter detail posted online by Beaumont, Port Arthur, Orange, or Jefferson County. Beaumont's subdivision code sends designers to the city's official street construction standards and specifications.

Jefferson County's subdivision rules point to the county's Road and Drainage Specifications, TxDOT manuals, and AASHTO policy.

For a published example, this page uses one from outside the region. Waco's standard detail ST-19, revised in 2025, requires a standard valley wherever runoff is carried across the street at an intersection.

ST-19 allows valley gutters only on local streets unless Waco's director of public works approves certain collector or minor-street crossings. Otherwise, arterial and collector streets are not crossed by a valley.

Inside parking lots, a valley gutter often runs down a drive aisle to carry sheet flow to an inlet.

Ribbon curb shows up along pavement edges that drain to a swale or ditch. Beaumont's code, for one, lets rural streets in agricultural-residential areas skip curbs and drain to open roadside ditches.

How They Carry or Edge Water

TxDOT's Hydraulic Design Manual limits how deep and wide gutter flow may spread before it obstructs the roadway. That spread depends on flow rate, gutter slope, cross slope, surface roughness, and inlet spacing.

TxDOT's ponded-width equations apply to sections with a constant cross slope and a vertical curb. For parabolic and other shapes, the manual refers designers to FHWA's Urban Drainage Design Manual, HEC-22.

A valley gutter has no vertical curb face, so it falls in that second group. HEC-22's fourth edition, published by FHWA in 2024, covers pavement drainage, gutter flow, and inlet design.

The engineer of record sizes the valley. The contractor's job is to build that shape to grade.

NRCS puts slopes on the Beaumont soil series, a benchmark clay of the area, at 0 to 1 percent. A valley built flat, or one that settles, holds water where cars cross.

Waco's detail makes the same point in a note: the upstream return of a valley must be built so water will not pond. The flow line is set with an instrument and checked again before the pour.

Ribbon curb works another way. It does not channel water. It lets runoff leave the pavement while keeping the edge from breaking down under wheel loads.

Construction and Jointing

Both start with compacted subgrade set to grade. Hollier's slip-form machine lays valley gutter on longer runs, and hand-form crews build the radii.

Reinforcement follows the governing detail. Waco's ST-19 shows an 8-inch concrete valley reinforced with No. 4 bars at 12 inches each way.

Joints have to agree with the pavement around them. TxDOT's CCCG-22 sheet says joints in curb and gutter next to jointed concrete pavement must match the pavement joints.

ACPA's guide to joints for concrete streets says the same. Transverse contraction joints must run continuously through the curb, or cracks form in the curb at each pavement joint.

ACPA's intersection layout method also avoids joints that meet each other or an edge at a sharp angle. Angles under 60 degrees are a concern, and about 90 degrees is the target.

Around each curb radius, ACPA draws a return line 1.5 to 3 feet from the gutter face. Any joint that reaches it is brought along the curve's radius to the back of the curb and gutter.

Tying Into Curb and Gutter Runs

A valley gutter rarely stands alone. At each end it meets a run of concrete curb and gutter. Water has to pass that joint without a lip or a low spot.

At an intersection, side-street gutter pans feed the valley, and the valley hands flow to the gutter beyond it. Matching those elevations is survey work before it is concrete work.

Where barrier or roll curb meets a valley or a ribbon edge, the curb face has to step down to the flatter section. That transition is hand-formed and belongs on the plans, not invented in the field.

Ribbon curb often ends at a driveway, a ramp, or a drainage structure. Paving and site preparation are also Hollier's own work. That lets the valley, the curb runs, and the pavement between them follow one sequence.

What is the difference between valley gutter and cross gutter?

In most plan sets they describe the same thing: a shallow concrete channel that carries water across or along pavement. Agencies pick one name for their standard details, so follow the term and the detail on your drawings.

When is ribbon curb a better choice than raised curb?

Ribbon curb fits where water should leave the pavement edge as sheet flow, such as streets that drain to ditches or swales. Raised curb fits where runoff must stay in a gutter and travel to inlets.

Can traffic drive over a valley gutter?

Yes. A valley gutter is built nearly flush so vehicles can cross, with a shallow dip that carries water. Its width and depth come from the governing detail, and Waco, for one, keeps valleys off most collector and arterial streets.

Is valley gutter reinforced?

Often, but the detail on the plans decides. Waco's standard, for one, uses No. 4 bars at 12 inches each way in an 8-inch slab. Build to the detail the reviewing agency approved.

Do you machine-lay valley gutter?

Yes. Hollier's slip-form machine lays valley gutter along with barrier and roll curb. Hollier's hand-form crews take the radii at each corner of the intersection.

Why does an existing valley gutter hold water?

Standing water usually means the flow line has settled or was built too flat. On level ground there is little room for error, so the fix is often removing the section and rebuilding it to a surveyed grade.

What keeps ribbon curb from cracking or breaking off?

A compacted base, contraction joints at regular spacing, and firm soil beside it. When the shoulder next to a ribbon curb erodes, the edge loses support, so keep that ground stable and covered with grass.

Which valley gutter detail applies on a Beaumont street?

Beaumont's code ties subdivision streets to the city's official street construction standards and specifications. That valley sheet does not appear to be posted online, so request the current detail from the Engineering Division before bidding.

TxDOT Hydraulic Design Manual: Section 4, Pavement Drainage

TxDOT Hydraulic Design Manual: Gutter Flow

FHWA (ROSA P): Urban Drainage Design Fourth Edition, HEC-22 (FHWA-HIF-24-006)

ACPA Wiki: IS061 - Design and Construction of Joints for Concrete Streets

ACPA Wiki: Joint Layout

TxDOT Standard Sheet: Concrete Curb and Curb and Gutter (CCCG-22)

City of Beaumont Code (eCode360): Article 26.03, General Design Principles and Specific Design Standards and Improvement Requirements

Jefferson County: Subdivision and Development Regulations (amended March 2026)

USDA NRCS: Official Soil Series Description, Beaumont Series

City of Waco: ST-19 Standard Concrete Valley and Concrete Curb and Gutter Fillet (out-of-region example)