ADA Curb Ramp Contractor in Southeast Texas

Hollier Construction Services builds ADA curb ramps across Southeast Texas with hand-form crews, alongside its concrete curb and gutter and sidewalk work. Each ramp is built to the TxDOT or municipal details on the plan set. This page summarizes the federal and Texas rules on ramp types, slopes, landings, flares, and detectable warnings. It is not legal advice.

Which Standards Apply in Texas

Two documents set most curb ramp rules on Texas sites. The Access Board says the 2010 ADA Standards apply mainly to facilities on sites. The Texas Accessibility Standards (TAS), administered by TDLR, took effect March 15, 2012, and repeat the same curb ramp text in Section 406.

Location changes the rules. TDLR training places curb ramps outside the public right-of-way under TAS 406 and ramps inside it under TDLR Rule 68.102. That rule also accepts the Access Board's right-of-way guidelines (PROWAG), as proposed in 2011 or as finally adopted. Per the training, projects let after May 15, 2017 must use PROWAG when federal money is provided.

The Access Board issued PROWAG as a final rule on August 8, 2023. It becomes mandatory once the Department of Justice and the Department of Transportation adopt it for enforcement.

Ramp Types: Perpendicular, Parallel, and Blended Transitions

TxDOT's Roadway Design Manual prefers two curb ramps per corner, each aligned with the desired path of travel. It notes that PROWAG requires two ramps or a blended transition.

Slopes, Written as Ratios

Section 406.1 of the 2010 ADA Standards applies the ramp rules in 405.2 through 405.5 to curb ramps, and TAS uses the same text.

Section 406.2 also requires the surfaces where ramp, walk, gutter, and street meet to sit at the same level. A lip at the gutter joint defeats a ramp that otherwise meets every ratio.

Landings, Flares, and Clear Space

Section 406.4 requires a landing at the top of each curb ramp. It is at least 36 inches long and as wide as the ramp, not counting flares. PROWAG landings are 48 by 48 inches minimum. A perpendicular ramp needs one at the top when a pedestrian must turn to reach it.

Flares are not part of the accessible route. The Access Board says side flares mainly prevent tripping where people may cross a ramp's sides. In alterations with no top landing, flares are mandatory and may be no steeper than 1:12.

A diagonal ramp needs a 48-inch clear space at its foot, outside active traffic lanes. At a raised island with ramps, each ramp needs a level area 48 inches long by 36 inches wide at its top.

PROWAG adds a 48 by 48 inch clear area beyond the bottom of a perpendicular ramp. At the gutter, it limits the change of grade or requires a transitional space at least 24 inches long at 1:48 maximum.

Detectable Warning Surfaces

Section 705 of both the 2010 ADA Standards and TAS builds detectable warnings from truncated domes. Domes have a base diameter of 0.9 to 1.4 inches and a height of 0.2 inch. They sit 1.6 to 2.4 inches on center, with at least 0.65 inch between bases. The field must contrast with the adjacent surface, light on dark or dark on light.

Where domes are required is a separate question. The Access Board says the 2010 ADA Standards require them on curb ramps only at transit facilities covered by DOT's standards. DOT also requires them on curb ramps in projects funded by the Federal Highway Administration.

PROWAG requires them at curb ramps and blended transitions, at least 24 inches deep across the full ramp run width, excluding flares. If both ends of a perpendicular ramp's bottom grade break lie within 60 inches of the back of curb, the field goes there. Otherwise it sits at the back of curb. TxDOT requires materials that meet its Pedestrian Facility Standards.

When Street Work Triggers New Ramps

Ramp duties can come from street projects, not only sidewalk jobs. Joint DOJ and DOT guidance from July 2013 treats resurfacing from one intersection to another as an alteration requiring curb ramps. That includes overlays, with or without milling, even at the same height.

Treatments that only seal and protect the surface, improve friction, or control splash and spray count as maintenance. Examples include chip seals, slurry seals, crack sealing, and pavement patching.

Hollier's hand-form crews build curb ramps within curb and gutter, sidewalk, and paving work across Jefferson, Orange, and Hardin counties. Each ramp follows the slopes, details, and dome layout on the approved plans. Questions about which standard governs a site belong with the project's design professional or TDLR.

What is the steepest slope allowed on an ADA curb ramp?

The 2010 ADA Standards and TAS cap the running slope of a curb ramp at 1:12 and the cross slope at 1:48. At existing sites short on space, Table 405.2 permits up to 1:10 where the rise is 6 inches or less. It permits up to 1:8 only where the rise is 3 inches or less.

What is the difference between a perpendicular and a parallel curb ramp?

A perpendicular ramp runs at a right angle to the curb line, and TxDOT treats it as the preferred type. A parallel ramp uses two runs that slope along the curb to a level landing between them. TxDOT describes parallel ramps as one solution on narrow sidewalks.

Does every curb ramp in Texas need truncated domes?

It depends on where the ramp sits and which standard governs it. The Access Board says the 2010 ADA Standards require domes on curb ramps only at DOT-covered transit facilities. DOT also requires them on projects funded by the Federal Highway Administration, and PROWAG and TxDOT's manual call for them. Follow the approved plans.

How big must the landing at the top of a curb ramp be?

Under the 2010 ADA Standards and TAS, the top landing is at least 36 inches long and as wide as the ramp, excluding flares. PROWAG calls for 48 by 48 inches at the top of a perpendicular ramp when a pedestrian must turn to reach it.

How does TDLR handle curb ramps on public streets?

TDLR Rule 68.102 covers public right-of-way projects. It accepts TAS or PROWAG, bases registration cost on the pedestrian elements only, and applies TAS only to pedestrian elements within the project scope. Owners should confirm registration and inspection steps directly with TDLR.

Does repaving a street require new curb ramps?

Joint DOJ and DOT guidance says resurfacing from intersection to intersection, including overlays with or without milling, is an alteration that requires curb ramps. Ramps built before March 15, 2012 that met the 1991 Standards or UFAS need not be upgraded. Ramp work may run under a separate contract if it finishes before or with the road work.

Are diagonal curb ramps still allowed?

TAS 406 still permits diagonal ramps when they have a 48-inch clear space at the bottom outside active traffic lanes. TxDOT's Roadway Design Manual says they may be used only where physical constraints make two ramps or a blended transition technically infeasible.

What should an owner have ready before a curb ramp project?

Have the approved plans, the ramp details, and any city or TxDOT standard sheets the design references. Know whether the ramp sits on private property or in the public right-of-way, because TDLR applies different rules to each.

ADA.gov: 2010 ADA Standards for Accessible Design

U.S. Access Board: Guide to the ADA Accessibility Standards, Chapter 4: Ramps and Curb Ramps

U.S. Access Board: Public Right-of-Way Accessibility Guidelines, Chapter 3: Technical Requirements

U.S. Access Board: U.S. Access Board Issues Final Rule on Public Right-of-Way Accessibility Guidelines

TDLR: 2012 Texas Accessibility Standards (TAS) Online

TDLR: TAS Chapter 4: Accessible Routes

TDLR: TAS Chapter 7: Communication Elements and Features

TDLR: Texas Accessibility Academy, Section 5: Accessible Routes & Curbs

Cornell Legal Information Institute: 16 Tex. Admin. Code § 68.102, Public Right-of-Ways Projects

TxDOT: Roadway Design Manual, 19.4 Curb Ramp Design

TxDOT: Roadway Design Manual, 19.4.5 Curb Ramp Types

ADA.gov archive: DOJ/DOT Joint Technical Assistance on Requirements to Provide Curb Ramps when Streets, Roads, or Highways are Altered through Resurfacing

ADA.gov archive: Questions & Answers, Supplement to the 2013 DOJ/DOT Joint Technical Assistance on Curb Ramps and Resurfacing